Product Description

The SKB line of 19" stackable racks has received worldwide acclaim for durability, convenience and easy handling. Made of ultra high molecular weight polyethylene, they are less than half the weight of old fashioned wood racks and provide maximum protection. Front and rear covers are gasket sealed to protect equipment from moisture and dirt. Rackable Mount Depth: 18 1/2". Front Rail to Rear Rail: 15 3/4" Lid Depth: 2 1/2".Max. Width: 17 3/4". Max. Height: 18 3/4". Exterior Dimensions: 21 1/2" W, 22" D, 20" H. Weight: 19.5 lbs. ... Read more

Features

• A quality product at a bargain price, with the Amazon.com assurance.

Product Description

The Line Level Shifter uses the physics of inductance and impedance matching to increase or decrease the signal voltage without the added noise of active electronics. The Line Level Shifter also converts back and forth between balanced and unbalanced signals automatically. It also contains Hum Eliminator technology to prevent groundloops that cause AC hum. ... Read more

Features

• Converts back and forth between -10dBV and +4dBu
• Built-in Hum Eliminator technology eliminates AC hum/60 MHz buzz and noise
• Automatically translates signal voltages to match differences in ground potentials, avoiding clipping
• Converts automatically back and forth between balanced and unbalanced lines at either end
• Completely passive design with audiophile quality components assures the best possible noise and distortion performance

Product Description

This great 11-gauge steel rack rail is punched and tapped for 10-32 in. screws. It is full hole rack rail with holes tapped at 5/8 in. - 5/8 in. - 1/2 in. Sold in pairs. Finished in a high-quality brushed black anodized finish. ... Read more

Product Description

Save BIG when you buy today! ... Read more

Product Description

Fully enclosed rack mountable drawers with spring loaded latch. Available in 2, 3, 4, & 5 rack spaces. ... Read more

Product Description

Economical steel flanged blank panels feature a rugged black powder coat finish. Available in 1 through 6 spaces. ... Read more

Features

• Powder coat is a superior finish to baked enamel

Product Description

Extra set of 4 casters for your Raxxess Converta Racks. ... Read more

Product Description

Roll-X cases have a depth of 17" and will accommodate 19" rack mount equipment with 3, 4, 5 and 6 rack space models. Made of polyethylene rotationally molded plastic with 2.5" wheels and industrial pull handle, the Roll-X racks interlock and stack with each other. ... Read more

Features

• Rotationally molded plastic
• 2.5" wheels
• Industrial pull handle
• 17" deep

Product Description

Kaces bags are made from the finest materials available. They use luggage-grade nylons, dense protective padding, instrument-friendly linings, and heavy-duty hardware. All bags are carefully crafted in their own factories to meet their high quality and value standards. ... Read more

Product Description

Rack tray for up to 2 UT4 receivers. Also use the URT with Shure LX3, LX4, SC4 and T4 Receivers, P6T and EP6T Transmitters, and PA760 and PA765 Antenna Combiners. ... Read more

Product Description

Transforms almost any home stereo component into a rackmount unit! Safely secure equipment with these clamping rackshelves.Adjustable rubber lined clamps secure unit from top, while adjustable "L" brackets secure unit from rear.Heavy duty, 16 gauge (.063") steel construction.Durable black powdercoat finish.14-1/2" depth. ... Read more

Product Description

1This great 11-gauge steel rack rail is punched and tapped for 10-32 in. screws. It is full hole rack rail with holes tapped at 5/8 in. - 5/8 in. - 1/2 in. Sold in pairs. Finished in a high-quality brushed black anodized finish. ... Read more

Reviews (1)

Good product for home studio
Very easy to install but since not all rack screws are standard, be sure to get the ones that sell for this product ... Read more

Product Description

New and Improved! New Roto-Molded ergonomic design with a completely adjustable pop-up Velcro? board on top to accommodate a wide variety of mixers and accessories. 6 space rackmount below. Roto-molded rock solid with improved locking systems. Lids, front panel and much larger rear access panel lift apart and re-assemble more securely. Top: 17 1/4" W x 16 1/4" D. Mounting Surface Depth 5 1/4" H rear -3" H front Depth slant. Bottom (6u) 17" from front of rail to back of case. Exterior Dimensions: 23 1/4" W, 24" D, 21 1/4" H. Weight: 41.0 lbs. ... Read more

Features

• 6 space rack-mount below.
• Roto-molded rack solid yet light weight.
• Handy side handles
• Stacks securely with SKB rackmount cases

Product Description

This great 11-gauge steel rack rail is punched and tapped for 10-32 in. screws. It is full hole rack rail with holes tapped at 5/8 in. - 5/8 in. - 1/2 in. Sold in pairs. Finished in a high-quality brushed black anodized finish. ... Read more

Product Description

The perfect feature for every rack has now arrived with the Gator Powered Rack! A built-in power distribution center provides 5 power sources, 15 amp push to reset circuit breaker, and front panel on/off control with pilot light. Available 4, 6 and 8 space. ... Read more

Product Description

Save BIG when you buy today! ... Read more

Product Description

This 5-1/4 in. (4-space) x 2-9/16 in. media holder has a black brushed finish and holds 27 DAT tapes. ... Read more

Product Description

Rack mounting kit for mounting one or two Evolution Wireless G2 rackmountable devices. Will not mount original generation rackmountable devices. ... Read more

Product Description

An attractive series of blank panels, BL products utilize a 16-gauge aluminum flanged design. Easy to machine, black brushed and anodized. ... Read more

Product Description

With today's ever-increasing amount of gear that contains disc drives and liquid crystal displays, the need for an affordable shock rack has become mandatory. Gator's new G-SHOCK deluxe shock rack cases are molded from an incredibly durable high-density military grade Polyethylene. This lightweight yet super strong material insures maximum protection at a weight you can easilyhandle.Gator uses rubber shock absorbers on all eight corners which assures a soft ride in every direction. The internal 19" rack frame has threaded front and rear rack rails. In addition, Gator has anotherexclusive – a moveable rear support system! This does away with needinga machine shop in your garage to make a rear support for your power amps or rack gear. Furthermore, those threaded rack rails are field replaceable.Exclusive to the Gator racks are locking front and rear lids. Slopedside handles molded from Polyethylene make these cases comfortable tocarry when the racks are loaded and they are virtually indestructible! The ridges on the top and bottom make these cases universally stackable with both Gator racks and those of other manufacturers who construct their product in accordance with E.I.A. specifications. Specifications:(Interior)*Total Rackable Height 14" (8U)*Front Rail to Back Rail 16-3/4"*Total Rackable Depth 19"*Case Lid to Case Lid 22"*Lid Depth 2-1/4"(Exterior)*Total 20" x 23" x 23" ... Read more

Features

• Gatorâs deluxe rack cases are molded from incredibly durable high-density military grade Polyethylene
• This lightweight yet super strong material insures maximum protection at a weight you can easily handle
• The cases have 19
• 5â of rackable depth with front and rear threaded rack rails that are field replaceable