Product Description

SheetBlok-Plus is a dense, limp-mass material that comes with a PSA (pressure-sensitive adhesive) already attached!Just peel off the PSA backing and apply the SheetBlok Plus to the area to be covered and that's it! And while it's not meant to be a permanent mounting solution, it will easily hold your SheetBlok up until you're ready to put the finishing layers over it. SheetBlok Plus eliminates the hassles of troweled-on adhesives and mechanical fasteners and can save tons of time. 4x30 roll, covers 120 square feet. ... Read more

Product Description

VB-TS is an adhesive backed, low profile combination thermal barrier and acoustic absorber.The 3/8" high temperature acoustic foam traps air and acts as an insulator while the aluminum mylar surface reflects engine heat.Additionally, the foam will absorb midband and high frequency mechanical noise generated by engine components.Designed primarily for engine compartments and other high heat areas. ... Read more

Product Description

The MIDI Solutions T8 8-output MIDI Thru Box is a 1-in 8-out MIDI Thru Box. All MIDI messages appearing at the input are sent to all eight Thru outputs. Active circuitry cleans up any skewing of MIDI data bits that has occurred at the input, insuring reliable operation in setups that require daisy chaining or long cable runs.MIDI-powered, it requires no batteries or power supply to operate. A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it. ... Read more

Features

• 1-in 8-out MIDI Thru Box
• Helpful in systems that daisy-chain or use long cable runs
• All input MIDI messages are sent to all 8 Thru outputs
• Active circuitry cleans up any skewing of MIDI data bits
• MIDI-powered, requires no batteries or power supply

Product Description

Provides a contact closure which can be programmed to open or close in response to 4 separate types of MIDI events: Note, Control Change, Program Change, or a System Exclusive event such as MIDI Show Control or Machine Control. A fast reed relay is used for response time of less than 2ms. Relay contact is rated at 500 mA. Connects through 1/4" jack. Relay is programmed via the Processors Programming Tools software and retains settings even after power is removed. Unit is MIDI powered and includes an indicator LED. 4.3 oz. 4-1/2"W x 2-1/2" x 1-1/4"D. ... Read more

Features

• Programmable
• Opens or closes in response to 4 separate types of MIDI events: Note, Control Change, Program Change, or a System Exclusive event
• Programmed via Processors Programming Tools software
• Retains settings even after power is removed

Product Description

The MIDI Solutions Merger is a 2-in 1-out MIDI Merger. All MIDI messages appearing at the two inputs are merged to the output. All MIDI data types are merged, including System Exclusive and MIDI Time Code. A fast merging algorithm insures that the MIDI data is processed with minimal delay. ... Read more

Features

• The Merger is MIDI-powered and requires no batteries or power supply to operate
• A MIDI indicator LED lights up when the product is powered and flashes when MIDI data passes through it

Product Description

With the MIDI Timepiece AV you can combine MIDI with ADATs (tm), ProTools (tm), or video. The MIDI Timepiece AV takes MOTU's world-renowned MIDI Time Piece II and adds synchronization that you really need, like video genlock, ADAT sync, and word clock sync. Even Digidesign superclock! Now you can Slave ADATs, Digidesign hardware or word-clock compatible devices to SMTPE and video. Drive your ADATs from your sequencer without an Alesis BRC (tm). Or control everything from an MMC controller like JL Cooper's CuePoint (tm). The MTP AV pulls it all together for stable, centralized, hassle-free synchronization and MIDI networking. For Macintosh, Windows, and stand-alone setups. The MIDI Time Piece AV provides eight discrete MIDI cables (in and out) for your computer. This allows you to use 128 independent MIDI channels. To expand beyond this, you can network up to four MTPs for a total of 512 MIDI channels. You can even connect two computers to an MTP AV network.The MTP AV is also an 8x8 merger and router. You can merge any combinations of the eight inputs simultaneously to any combination of the eight outputs. Because the MTP AV's internal memory can be programmed from the front panel,the MTP AV is the perfect choice for live performance applications where fast and flexible MIDI patching is essential. You can take the MTP AV on the road because it can operate with or withou... ... Read more

Features

• Built upon the MIDI Time Piece II
• Add synchronizations such as video genlock, ADAT sync, word clock sync, and Digidesign superclock
• Lets you slave ADATs, Digidesign hardware, or word-clock compatible devices to SMTPE and video
• Allows you to drive ADATs from your sequencer without an Alesis BRC
• Gives you stable, centralized, hassle-free syncing and MIDI networking

Product Description

A great all-around acoustic absorber that's twice as absorbent as 2 inch Studiofoam at 125Hz. 3 inch Acoustic Studiofoam can do many of the same things 4 inch can do (especially when used with LENRDs or Venus Bass Traps) and can provide a drier, more anechoic sound in any size room. Highly recommended for superior acoustic sound control. Includes 8 - 2'x4' foam pieces (64 sq. ft.). ... Read more

Product Description

Combines an acoustic foam absorption panel with specially engineered air cavities to yield extraordinary sonic benefits. The VersaTile design allows it to be used in a variety of ways. It can be positioned to bridge a corner, creating a sizable air pocket that gives you some great low-frequency absorption. It can also be placed on walls and ceilings with either side out, allowing for some sophisticated looks while offering superior absorption characteristics versus thinner, flat acoustic foam panels. 16 panels cover 64 square feet. ... Read more

Features

• Combines an acoustic foam absorption panel with specially engineered air cavities
• Can be positioned to bridge a corner
• Can also be placed on walls and ceilings with either side out
• Superior absorption characteristics versus thinner, flat acoustic foam panels
• 16 panels cover 64 square feet.

Product Description

CornerFills are sections of flat-cut Studiofoam corner acoustic absorbers that are beneficial in 2 ways. Aesthetically, they give you smooth, clean edges against which to butt your acoustic wall treatments and acoustic foam bass traps for a more professional appearance. Acoustically, they smooth out the excess low-frequency energy that congregates in room corners. Great for gyms and larger rooms. 4'x4'x24". ... Read more

Product Description

Both VB-3 and VB-4 are designed to yield maximum attenuation over a broad frequency range.Both offer a significantly higher transmission loss than damper alone.The VB-3 with its lead septum is used in areas where highly flexible and moldable barriers are required, like firewalls and transmission tunnels.The VB-4 with its loaded vinyl barrier is better suited for flat, high impact and high traffic areas, like trunks, floorpans and truck beds.Cabin flooring for both RV and marine are also excellent application areas.VB-3/VB-4 thickness: .250".Not adhesive backed. ... Read more

Product Description

The Venus Bass Trap achieves a prodigious level of low-frequency sound control at your room boundaries, where low-frequency problems begin, at a price that allows it to fit into most budgets. Venus Bass Traps ship in a 2x4x1 ft. size, but are often cut in half to 2x2 ft., then paired with a 12 inch CornerFill. While the Venus Bass Trap provides low frequency sound control and broad bandwidth absorption that's second to none in all rooms, it really shines in larger rooms like gymnasiums, houses of worship, and multipurpose rooms. ... Read more

Product Description

The Venus Bass Trap achieves a prodigious level of low-frequency sound control at your room boundaries, where low-frequency problems begin, at a price that allows it to fit into most budgets. Venus Bass Traps ship in a 2x4x1 ft. size, but are often cut in half to 2x2 ft., then paired with a 12inch CornerFill.While the Venus Bass Trap provides low frequency sound control and broad bandwidth absorption that's second to none in all rooms, it really shines in larger rooms like gymnasiums, houses of worship, and multipurpose rooms. ... Read more

Product Description

Made from high-grade, studio-quality grey foam. Super dense for efficient sound reduction, and super tough so it won't tear or mutilate. Includes 12 - 2' x 4' foam pieces (96 sq. ft.). ... Read more

Product Description

A flexible acoustical absorber that features a 24" x 48" panel section made with 3" thick Primafoam high-density open-cell acoustical foam for maximum absorption in the critical mid and upper bands. As with all Primacoustic panels, Primafoam is embedded with a fire retardant to meet the California 117 code, making the Freeport safe for use anywhere. At just under 6' tall, Freeport is the perfect height to fit behind speakers, around a mix position, or as a gobo to reduce splash from instruments when recording. For voice-overs, 2 Freeports create a quiet reflection-free zone that really works! This flexibility makes Freeport a must-have for any studio. Unlike other portable systems that use wobbly mic stands as their base, Freeport features an unbreakable integral frame and sturdy base made from rugged PVC that's easy to assemble and sets up in minutes. The internal frame may be permanently glued together or assembled on the spot, then disassembled for storage in its box.The internal frame extends the length and width of the panel to ensure it will not droop over time. The versatile offset T-base can be set up in various configurations for uses such as under a desk, grouped in a semi-circle, or even flat against the wall. ... Read more

Product Description

LENRD stands for Low-End Node Reduction Device. (As you may know, a resonance bump in a room's frequency response is called a room node. Now, thanks to LENRD, you can achieve low frequency accuracy other companies can't give you!Bass traps substantial enough to control nodes have always been expensive to buy or intricate and time-consuming to build, but not anymore! LENRD is extremely effective at smoothing out low frequency room nodes at a price that anybody can afford! 16 linear feet per box. ... Read more

Product Description

The Venus Bass Trap achieves a prodigious level of low-frequency sound control at your room boundaries, where low-frequency problems begin, at a price that allows it to fit into most budgets. Venus Bass Traps ship in a 2x4x1 ft. size, but are often cut in half to 2x2 ft., then paired with a 12inch CornerFill.While the Venus Bass Trap provides low frequency sound control and broad bandwidth absorption that's second to none in all rooms, it really shines in larger rooms like gymnasiums, houses of worship, and multipurpose rooms. ... Read more

Product Description

VB-2 is a flexible, odorless and lightweight mineral filled vinyl-copolymer damping sheet.It has twice the damping and less than half the weight of asphalt damping materials and the ability to handle continuous temperatures to 250° F.For heavy duty damping requirements, VB-2HD is the perfect material.Both models feature a modified acrylic peel and stick adhesive that does not require the use of a heat gun for installation and are ideal for damping sheet-metal, plastic, fiberglass and wood.VB-2 thickness: .040".VB-2HD thickness: .075". ... Read more

Product Description

With the help of U-Boats, a floated room features improved transmission loss (isolation) and low frequency definition. Available in boxes of 50 and 200. ... Read more

Product Description

The VE-1 was formulated for maximum damping efficiency over a broad frequency and temperature range.It is made of a mineral filled viscoelastic polymer that transforms vibrational energy into thermal energy (low level heat). It provides twice the damping of asphalt based product without the weight and odor. The VE-1 has a grain leather finish and is cosmetically pleasing, so it can be used on front speaker baffles and other applications that are visible to the eye.The flexible nature of the VE-1 damping sheets enables it to mold and conform to irregular surfaces.It can be easily cut using a standard razor knife or scissors.The pressure sensitive adhesive makes for easy peel and stick installations and will adhere to most surfaces including metal, wood and fiberglass.Excellent flame resistance, can handle continuous temperatures up to 250° F and meets UL94V-O. Thickness: .050". ... Read more

Features

• Twice the damping and half the weight of asphalt based damping sheets
• Easy peel and stick application
• Makes excellent gasket material

Product Description

The perfect product for the budget conscious yet acoustically discerning customer. Sonomatt is cut in the industry standard eggcrate style to keep its price low, but it still outperforms competitors' premium brands! ... Read more