Product Description

Features: 300 watts continuous, 1,200 watt peak power handling. Delivers over 125 dB continuous, 131 dB peaks (1 w / 1 m) at full power. 65 x 65 Constant-directivity horn allows use vertically or horizontally with identical coverage. Delivers better pattern control and projection than typical 90 degree horns Proven, reliable EV components including DL12BFH cast-frame 12-inch woofer and DH2010a pure titanium compression driver Ring-Mode Decoupling (RMD) delivers unexcelled vocals and pure, accurate instruments and mids Rugged, durable polypropylene enclosure is light and strong. Built-in stand mount and inserts in enclosure allow the system to be safely suspended and arrayed using a wide range of optional cost-effective hardware. Can also be used as a floor monitor with F200 attachment Parallel Neutrik Speakon input connectors for safe, loss-free connections ... Read more

Product Description

Comprised of dual 6-inch LF drivers and a 1-inch Ti/waveguide, the EVID 6.2 is perfect for applications that require exemplary audio and the capability to fill large areas with sound. Additionally, the flexible Strong-Arm-Mount? (SAM?) system provides the versatility to accommodate any installation challenge. EV's unique 6-inch dual woofer design delivers crisp and clean program for the utmost in listening experience regardless of the location. Great for larger areas that demand higher SPL levels, the 6.2 delivers the outstanding, full bass output required for shopping malls, stadiums, airports, etc. Specifications: Frequency Response (-10db): 62Hz-20kHz. Power Handling: 300W Cont. Prog./600W Peak. Sensitivity: 94dB, 1W, 1m. Impedance: 8 Ohms. Max SPL: 118dB. Horizontal Coverage: 100 degrees. Vertical Coverage: 80 degrees. Crossover Frequency: 1.6 kHz. LF Transducer: 2 x 6" (100 mm). HF Transducer: 1" (25 mm). Protection: Full System. Weather Resistance: Meets Mil Spec 810 humidity, salt spray, temperature and UV, and IEC 529 IP 34 splashproof ratings. Swing x Rotation: 100 deg. x 90 deg. Terminals: Spring. Enclosure Material: ABS (paintable). Dimensions (HxWxD): 16.5" x 9" x 11.75". Net Weight (each): 12 lbs, Shipping Weight (pair): 27 lbs. Included Accessories: SAM, hex key. ... Read more

Features

• Line-array enhanced coverage control
• Strong-Arm-Mount for easy, flexible aiming
• Full-bandwidth overload protection
• Weather resistant - Conforms to Mil Spec 810 and IEC 529 IP 34
• Magnetically shielded

Product Description

Three super bullet tweeters Inputs: Dual 1/4", Banana & Binding post Carpet finish and corners Frequency Response: 60Hz-18kHz Sensitivity: 91db Impedance: 8 ohms Dimensions: 20"H x 13"W x 10.5"D Shipping weight: 22 lbs. ... Read more

Product Description

The Electro-Voice Sx300 is a 300-watt, 12-inch two-way, high-efficiency, constant-directivity compact speaker system with Ring-Mode Decoupling. Through the extensive use of computer-aided design and modeling, Electro-Voice engineers have developed a state-of-the-art professional loudspeaker system. The high-frequency section of the Sx300 utilizes a molded-in, 65° x 65° constant-directivity horn. This unique pattern contributes to high intelligibility, vocals sound natural yet ?cut through? in reverberant, noisy rooms. In addition, the coverage pattern is unusually uniform over its range of operation. Sound quality off axis is very well maintained, even at 45° off axis (a 90° total coverage angle), beyond the rated coverage angle. The horn's unique, Varipath throat geometry helps direct driver output to the corners of the room, this helps cover areas of the audience that typically do not recieve good coverage. High-impact polypropylene structural foam provides a stiff and extremely durable lightweight enclosure. Molded into the cabinet are an integral carrying handle and a stand socket for mounting on 1-3/8-inch stands such as the Electro-Voice 100BK. Rubber feet that are attatched to the bottom of the cabinet and mating sockets that are molded into the top provide a means of stacking systems. Sold individually. Shipping weight: 41.00 lbs. ... Read more

Features

• 12" 2-way speaker
• 300W Continuous, 1200W Peak
• Frequency Range (-10 dB): 50 Hz - 20 kHz
• Dimensions (H x W x D): 23.1" x 16.9" x 12.3"
• Dual Neutrik Speakon® high-current connectors

Product Description

Produce a superior three-dimensional sound field Perfect for listening to a vintage jazz album or the latest action/adventure DVD Recommended Power: 10 - 120 watts Frequency response: 45 - 20,000 Hz, ± 3 dB Impedance: 8 ohms, nominal Efficiency: 91 dB SPL from 2.8 VRMS Crossover: 2-way, passive multi-element design with 12 dB/octave slopes Driver Protection: Automatic tweeter protection Enclosure type: Acoustic suspension, textured aluminum Finish: Charcoal gray Grille: Black, acoustically transparent, perforated steel Dimensions: 15 5/8"H x 7 1/4"W x 9 3/4"D Weight: 39 lbs. (each) ... Read more

Product Description

The new Gemini GX speaker range includes the very latest technology in lightweight ABS design. Trapezoidal design for a more precise and accurate sound these speakers will add increased sound definition on vocal frequencies. ... Read more

Product Description

Powered 12" 2-Way Loudspeaker - Professional ABS Molded Loudspeakers* The new Gemini GX speaker range includes the very latest technology in lightweight ABS design. Trapezoidal design for a more precise and accurate sound these speakers will add increased sound definition on vocal frequencies as well as your program music. *All speakers come with a protective speaker bag and stand mounts to turn your GX speakers into stage monitors ... Read more

Features

• 200 Watt RMS Power Handling Capacity
• 800 Watt Peak Power Handling Capacity
• 38 mm Stand Mounting Socket
• Auxiliary Line Outputs
• Metal Corners/Full Metal Grill

Reviews (1)

Good Speakers, Bad Internal Amplifier
I'll start this out by saying I bought a pair of these, Hooked them up, turned them on and the fuses blew on them after only 5 minutes of medium volume play. I replaced the fuses and they blew immediately. I took the amps out and had a look at the amp's design and was very shocked at the inconsistent and poor build.The MOSFETS, aren't even attached to the heat sink.I've never seen an amp that didn't mount the MOSFETs directly to the heat sink.This defeats the entire purpose of the heat sink. The low-pass crossover in one unit had a 15 guage inductor coil, and the other one had an 18 guage inductor coil.One of the resistors was shorted out against another due to improper installing.The location of the frequency cancellation magnet, which the power supply runs through in order to eliminate hum, is only half an inch away from the low pass inductor, which can change the inductance of the circuit causing a different cross-over point than intended.I highly recommend that you don't buy either one of the powered units from Gemini. ... Read more

Product Description

4X10" TWEETER HORN ... Read more

Product Description

19" x 10" wide dispersion radial horn High performance compression driver 2-way crossover Inputs: SpeakOn & Dual 1/4", Banana & binding post Heavy duty steel handles & steel corners Carpet finish Impedance: 8 Ohms Frequency response: 24Hz-20kHz Sensitivity: 115db Dimensions: 21.5"W x 50"H x 23"D Shipping Weight: 133 lbs. ... Read more

Product Description

The Electro-Voice ? SxA100+ sets a new standard for powered speakers. Its design provides the user multiple inputs with mix capability, an easy to use EQ section, and plenty of power in very compact, attractive package. This is a full range loudspeaker ideal for most applications requiring high-quality sound. Careful attention to the dynamic requirements of music guided the amplifier design to provide high SPL without excessive heat. The high quality microphone preamplifier provides great sounding vocals or speech. A master level control sets the desired SPL, and the line input can be mixed and balanced with a microphone with its level control. Its linear response is easily optimized for speech or music with the on board multiband equalization. Features:Compact, ergonomic sizeMic and Line inputs with mix capacity350 W dynamic LF power80 W dynamic HF powerLF and HF equalizationLine output for additional speakers65? x 65? constant coverage hornHigh sensitivity, 124 dB maximum SPLDynamic filters provide overload protection and linear responseMolded-in pole mount, easily suspendedDriven by the DH2010AF200 monitor feet includedSpecifications:Frequency response (-10 dB): 50Hz-20kHzMax SPL: 124 dBHorizontal Coverage: 65?Vertical Coverage: 65?LF Amplifier Power: 350W 50ms burst, 150W ContinuousHF Amplifier Power: 80W 10ms burst, 50W ContinuousMic Input Sensitivity: -35 dBu to 0 dBu for full... ... Read more

Product Description

Compact, passive, 2-way floor monitor. Loaded with a 12" LF driver and a 1" HF compression driver on a 70 x 40 HF horn. Low-profile, symmetrical enclosure. Has a built-in 2 stage high frequency protection system to guard against HF driver overload. Constructed from birch plywood, fitted with flush handles, polemount socket, rubber feet, internal M10 rigging points, and 2 Speakon NL4MP connectors. 600W handling. ... Read more

Features

• Passive 2-way, full-range loudspeaker
• 12" driver
• High-frequency speaker protection
• 600W handling program
• Birch plywood construction

Product Description

4" x 10" high compression horn Two bullet super tweeters 3-way crossover Inputs: Dual 1/4", Banana & Binding post Frequency Response: 30Hz-20kHz Impedance: 8 ohms Sensitivity: 105db Dimensions: 24.5"W x 33.5"H x 20.25"D Shipping weight: 108 lbs. ... Read more

Product Description

Features: 12" woofer with high temperature voice coil 4" x 10" high-compression horn Convenient latching system for speaker transport 2-way crossover Inputs: Dual 1/4", Banana & Binding post Carpet finish, corners, heavy duty handles Frequency response: 30Hz-20kHz Impedance: 8 ohms Sensitivity: 108db Dimensions: 19"W x 49"H x 15.75"D Shipping weight: 90 lbs. (per pair) ... Read more

Product Description

The next generation Explorer Pro is perfect for sound projection in indoor or outdoor settings and playing music during school activities. The unit delivers 110dB of intelligible speech from one sound system designed for users with no technical knowledge. The new Explorer Pro is truly versatile with true AC/DC, a 110/220 power supply and improved battery life. The system is ideal for schools, corporate trainers and places of worship. Features:Weather Resistant speaker ConeUV Treated - Fade Resistant CaseSpeech Projection SwitchBuilt-in CD and UHF Receiver OptionRugged CD Mechanism with Blue Back-lit DisplayIntegrated Circuit Amplifier w/Short Circuit and Thermal Overload ProtectionBass and Treble ControlsXLR Balanced Output, XLR Balanced Mic Input1/4" Line InputSpeakon® Output for XTR-6001Specifications:Rated power output: 60 watts AC mode / 30 watts DC modeW/ companion speaker: 80 watts AC mode / 60 watts DC modeMax SPL @ rated power: 110 db @ 1 meterFrequency response: 80 Hz - 16 kHzMicrophone inputs (2 universal jacks):Lo-Z (1 kOhm), balanced, XLR12 VDC condenser mic (phantom) powerHi-Z (10 kOhm), unbalanced, 1/4"-phoneAuxiliary (line) input: Hi-Z (10 kOhm), unbalanced, 1/8” stereo, 1/4"-phoneSensitivity for rated output, dual RCA/1/4” unbalanced/balanced 1/4"-phoneAC Power requirements: 90 - 264 VAC, 50/60 HzDimensions 16.5 x 10.5 x 10" Weight: 23 lbs ... Read more

Product Description

8 Ohm Impedance 300 Watts RMS/700 Watt Peak Resonance: 48Hz Frequency Response: 40Hz - 4kHz Average Sensitivity: 103 dB (1W @ 1m) 50 oz Magnet Overall Diameter: 14.562" Depth: 6.06" Pressed Steel Frame ... Read more

Product Description

Features: 12" woofer 12" horn Three 3" tweeters Metal corners Full metal corners 8 Ohms 200 watts ... Read more

Features

• 12" woofer
• 12" horn
• Three 3" tweeters
• Metal corners
• Full metal corners

Product Description

12" woofer in a scientifically ported cab with a 18" HF driver on a 90° horn provides solid lows and great dispersion. EAW's FR Series is designed for musicians and DJs who play small-to-medium-sized venues and require highly accurate sound but don't have a lot of capital. 18-ply-to-the-inch Baltic birch construction with durable polyurethane coating and ergonomically placed handles make the cab long-lasting and easy to move. Professional-quality transducers, complex asymmetrical crossover slopes, and internal passive filters provide amazingly accurate sound. Works with the FR250z subwoofer polemount base to create an instant full-range PA. 500W handling. 2 parallel Neutrik NL4 Speakon connectors. 15"W x 22.5"H x 14.75"D. 49 lbs. ... Read more

Features

• 12" woofer in a scientifically ported cab
• 18" HF driver on a 90 degree horn
• 18-ply-to-the-inch Baltic birch construction
• Durable polyurethane coating
• Ergonomically placed handles

Product Description

OmniMount's Professional Series isthe top-of-the-line speaker mounting solution assembly, tops for functionality, safety, ease of installation, appearance, and multi-application usage. ... Read more

Features

• Sold separately as wall or ceiling mount
• Black finish
• Supports speakers up to 120 lbs.
• 1" - 14 thread pattern

Product Description

The SR4725X 15" two-way compact speaker is a favorite for most general music and speech applications. Its 15" two-way design produces extended low frequencies in a transportable enclosure. ... Read more

Product Description

The EON 1500 combines legendary JBL EON sound quality with great transportability. Lightweight (only 38 pounds!) and ergonomically designed handles (balanced to the box's center of gravity) have taken the grunt work out of setting up for the gig. And EON's unique multi-angle enclosure gives you flexibility. The EON 1500 can be used as a Front-of-house PA speaker (floor-standing or pole mounted) or a Floor monitor with dual angles. The EON 1500 can also be used for fixed installations. This is a 15" 2- way speaker with a frequency response of 55 Hz to 16 kHz. Impedance is 8 ohms and power handling is 225 watts continuous and 900 watts peak. Handsome, all black enclosure is unobtrusive and professional in appearance. Enclosure and baffle are molded of tough, durable co-polymer material. EON 1500 will stand up to impact that would cause the joints on a conventional enclosure to separate. A heavy- duty, perforated metal grill protects the woofer. Dimensions: 27" x 17" x 17.5" Weight: 46 lbs. ... Read more