Product Description

Active Directional Antenna for U4S and U4D Receivers or UA845 Antenna Distribution System, 782-810 MHz Covers UA Frequency Range.The Shure UA870 is an active UHF wireless directional antenna featuring a log periodic dipole array. When compared to an omnidirectional 1/2-wave antenna, the cardioid pattern provided by the UA870 offers enhanced reception of the desired coverage area and greater rejection of RF signals outside the coverage area.To compensate for coaxial cable signal loss, the UA870 has an on-board amplifier that offers user selectable 3 or 10 dB gain. The gain setting is indicated by two LEDs. Remote 12 Vdc power for the antenna amplifier is provided by a Shure U4 Receiver or a Shure UA840 Antenna Distribution System through the connecting coaxial cable.The UA870 can be mounted on a microphone stand, suspended from the ceiling, or mounted to a wall using the integrated swivel adapter bracket. The UA870 is weather resistant for use outdoors. For best diversity performance, use two UA870 antennas. ... Read more

Product Description

Microphone clamp for AKG C1000 / D202. ... Read more

Product Description

The Choice of Broadcasters and Studio Engineers. Height Adjustable all black Shaft from 9.5 inches to 15.5 inches and a locking clutch. ... Read more

Product Description

The Shure Model WA380 Half-Wave Antenna for the LX2, LX4 and SC4 receivers provides up to 3 dB more gain than the standard quarter-wave antennas supplied with Shure wireless microphone receivers. When remotely locating an antenna away from the receiver, the WA380 Half-Wave Antenna must be used instead of the standard quarter-wave antenna.The WA380 Antenna Kit consists of the following items: Half-Wave Antenna (multi-section, telescoping), Right Angle Adapter, Mounting Bracket, and Straight Adapter with hexagonal nuts. ... Read more

Product Description

Windscreen for shotgun microphones. ... Read more

Product Description

A lightweight tripod stand and boom built to K&M's demanding standards. Features include a fiberglass reinforced base, two-section telescope pole with durable clutch and a one piece adjustment boom. Available in black only. ... Read more

Product Description

The M1 simply clamps and locks to rims and stands. ... Read more

Product Description

The Thunder boom has 4 degrees of freedom. Adjust front-to-back, up-and-down, side-to-side and rotationally by tightening just one knob. Designed to eliminate sag.Squeeze the "FLASH" base lever to quickly open the legs in one easy "umbrella style" motion. Release to lock the legs in place both in the open and closed position. There has never been a faster set-up.Ergonomic clutch is designed for quick and easy adjustment. ... Read more

Features

• Height 36-63 inches (914mm-1600mm)
• Boom Length 21.8-39.5 inches (452mm-1003mm)
• Weight 4.625 lbs. (2.1kg)
• Folds Compactly
• Easily folds to a compact and portable size

Product Description

The SM PR8 provides eight channels of balanced input, with a full-range of gain control from -20dB to +40dB and phantom power for every channel. It features no-compromise circuit design and the finest quality components. Its operational amplifiers are exceptional, offering extreme linearity and very low distortion. Equipped with eight balanced XLR analog inputs on the front panel and eight balanced TRS outputs on the rear panel. Internal power supply. Single rackspace mounting. ... Read more

Features

• Eight channels of balanced input/output
• Full-range gain control from -20dB to +40dB
• Phantom power for every channel
• Exceptional amplifiers
• XLR inputs (eight) on front panel

Product Description

The AT8647QM/S shock-mount plates effectively isolate mounted microphones from impact vibration and mechanical noise normally transmitted from the surface. They are intended for use with microphones mounted on lecterns, pulpits, conference tables and similar surfaces. Designed especially for UniPoint gooseneck microphones, they may be used with other lightweight microphones as well. This model incorporates a sturdy yet flexible suspension panel which provides the mechanical isolation. The AT8647QM/S accepts plug-in mics and features a phantom-powered mute switch with a lighted "on" indicator. AT8647QM/S with XLRF connector mount and lighted mute switch (48V phantom power required for operation). ... Read more

Product Description

Do you mic your amp? Buy this handy, all-metal accessory, and a gooseneck, too. Mount it on your amp, and get that extra mic stand out of your way forever! 5/8 in. flange with base holes on 1-1/4 in. mounting centers. ... Read more

Product Description

These heavy-duty, flexible 5/8"-27 thread mic clips feature a softer, more flexible clamp and will accommodate many different mic sizes. ... Read more

Product Description

This tough foam windscreen fits over most handheld microphones in the style of the Shure 58, AKG 950, Samson Q7, etc. Keeps your mic element safe! Tear-resistant for long life. ... Read more

Product Description

The D-FLEX is a gooseneck drum attachment for mounting Audix D-seriesinstrument & drum microphones to drums or amplifiers. The flexibility of its design allows for a variety of mounting positions and angles(dual pivot clip with extra wide claws). It will work with all other microphone clips using a 5/8" thread. ... Read more

Product Description

This is a snap-on, quick-release accessory that provides for instant connection and disconnection of mic holders and boom attachments with standard 5/8 in., 27 threads. ... Read more

Product Description

5/8"-27 (16mm-686mm) female to 3/8" (10mm) male. ... Read more

Product Description

1/2-Wave Dipole Antenna, for U4D, U4S, ULXP and ULXS recievers, 554-590MHz. ... Read more

Product Description

Remote Antenna Extension Cable BNC-BNC, RG8X/U type, 50 foot (15 m).Compatible with ULXS4, ULXP4, UC4, U4S and U4D. ... Read more

Product Description

Freedom One-hand stacking stand with curved ergonomic hand clutch. Easily adjust height with a quick squeeze. Stacking base up to 6 stands in 1 square foot of space. Lifetime warranty. ... Read more

Product Description

Single Rack Mount Kit for one ULX receiver.NOTE: If you are mounting a Shure unit with a metal chassis, use the 1/4 inch screws.NOTE: If you are mounting a Shure unit with a plastic chassis, use the 1/2 inch screws. ... Read more